1. Where is the core technology of BMS?
The core role of BMS is to ensure the safety of power batteries and improve Battery life. The technology cannot be measured by one or two indicators. The key is the experience of BMS manufacturers and the understanding of the performance of the corresponding types of batteries. At present, 80% of faults in new energy vehicles come from battery packs, and 80% of battery pack faults come from BMS, which shows the importance of BMS.
2. What is the difference between BMS for lithium iron phosphate and ternary battery?
Lithium iron phosphate BMS is less difficult and the ternary battery is more difficult. There are two main types of power battery options in the market: 1 ternary battery + efficient battery management system BMS, 2 lithium iron phosphate battery + relatively simple battery management system. The ternary battery has higher energy density, but its safety performance is less. It is easy to cause safety problems during overcharge and overdischarge. The ternary cell has less capacity and more quantity. When the cell inconsistency is not good enough, BMS plays a key role. Sexual effect. In other words, solving the safety problem of the ternary battery depends not only on the improvement of the quality of the battery but also on the BMS technology. Taking the CATL square as an example, the ternary battery capacity is 6~42AH, and the lithium iron phosphate battery is 50~200AH. The monomer capacity is large, and the smaller the number of battery packs of the same capacity, the technical difficulty of BMS is naturally reduced. . Tesla battery pack uses 18650 consumer batteries, its single capacity is only 8-10w, a battery contains more than 7000 single cells, its BMS difficulty is self-evident.
3. What is the difference between BMS for passenger cars, passenger cars and special cars?
Passenger car BMS is the least difficult, followed by the special car, the passenger car is the most difficult. The passenger car has a large space, the energy requirement of the battery is low, and the lithium iron phosphate is relatively safe. In 2015, 90% of the passenger car battery in China is lithium iron phosphate, and the corresponding BMS is also less difficult (as described in Article 2). . Passenger cars are generally operated by dedicated lines, and the shortcomings in the BMS technology can be compensated by the later services. The passenger car has a small space and requires high energy density of the battery. Most of the three-way batteries are used. In 2015, the proportion of the three-way battery of the passenger car is 60%, and the requirement for BMS is naturally higher. In addition, passenger car competition is relatively market-oriented, and its supplier system entry barriers and technical level requirements are also much higher than passenger cars. The ternary penetration ratio and technical grade requirements of the car are between the passenger car and the passenger car, and the BMS difficulty is also between the two.
4. What is the difference between passive equalization and active equilibrium?
Passive equalization generally uses the method of resistor heat release to release the “excessive power†of the high-capacity battery to achieve the purpose of equalization. The circuit is simple and reliable, the cost is low, but the battery efficiency is also low. When the active equalization charging, the excess power is transferred to the high-capacity battery, and the excess power is transferred to the low-capacity battery during the discharge, which can improve the use efficiency, but the cost is higher, the circuit is complicated, and the reliability is low. In the future, with the improvement of the consistency of the battery cells, the demand for passive equalization may be reduced. At present, the mainstream BMS factories in the country adopt passive balance.
Table 1: Balanced technical situation of major domestic BMS plants
5. What is the unit price of BMS? What is the proportion of the entire battery pack?
Bus battery capacity is large, voltage level is high, BMS is also more expensive, the unit price is about 10,000. The passenger car has a low voltage rating and the BMS unit price is around 3,000. The bus BMS unit is about 5000.
6. What is the cost of the BMS, PACK and battery of the battery pack?
Taking the 18650 battery as an example, the current price of the battery is 1.3 yuan / w, calculated according to the passenger car 25 degrees, the total price of the battery is 33,000, the price of BMS is 0.3 million, and the price of PACK is 14,000.
Figure 1: BMS and PACK cost ratio
Source: Lithium Battery and Battery Management System, Guotai Junan Securities Research
7. What is the market space for BMS, PACK and battery packs?
The unit price of BMS is relatively low, and only the BMS market space is small. In 2016, the market space is about 3 billion. However, if BMS is used as the core technology to introduce PACK, the market space is much larger. In 2016, the PACK battery pack space reached 44 billion, even After deducting the battery core, there are 14 billion market spaces.
Table 3: BMS, PACK, and Battery Pack Market Space Estimation
8. What is the development trend of the BMS industry?
At present, there are three types of companies engaged in BMS, automakers, battery factories and third-party BMSs. The representatives of domestic automakers are mainly BYD. The BMS and PACK of battery packs are mainly concentrated in the passenger car field. The technical level is relatively low. The three parties are concentrated in the field of passenger cars and special vehicles, and the technical level is obviously high. For example, Huasheng Power's founding team comes from Tesla, and its technical strength ranks among the best in China. The customer focuses on passenger cars (Jianghuai-based). Regarding the development trend of the industry, we believe that the core technology of the battery management system lies in software, and the battery core is in the electrochemical industry. It is difficult to develop software technologies such as BMS. The core competitiveness lies in the use of scale to reduce costs and provide high standards. Consistent products are quite different from the BMS and PACK industry custom attributes, and entering the BMS and PACK industries is not conducive to their advantages. A few whole-industry chain-integrated automakers can master BMS technology, and have their own production or no cost advantage. With reference to the automotive electronics industry, the entire vehicle is almost not involved in the manufacture of automotive electronics, and is completed by professional suppliers such as Bosch. We believe that in the future, BMS and PCAK will be mainly supplied by professional third-party companies and form a good cooperative relationship with OEMs.
Experts keep working hard and provide this Garden Light in the market in proper safe packing. These lights are made of damage free parts.
Backed by a team of knowledgeable professionals, we are an identified firm in the market for providing an extensive range of Garden Light.
Keeping in mind the requirements of customers, we are engrossed in providing Garden Lights. These lights are developed with the help of modern machinery and technology to ensure no scope for defects.
Garden Light,Solar Led Garden Light,Solar Lawn Garden Light,Decorative Garden Light
Delight Eco Energy Supplies Co., Ltd. , https://www.cndelight.com